Asante-technologies AWRT-600N Manual de usuario

SmartHub Dual Band 802.11 a/b/g/n Wireless Router Model AWRT-600N User’s Manual

Step 4 Turn on the computer. Step 5 Log in to the router and select the Status tab. Step 6 Verify that the Internet IP Address, Default Gateway, and a

5. Connecting to the Router Wirelessly Below are the default wireless settings of the router. You must configure your wireless network card to the sam

6. Web Configuration Utility This router has a built-in web configuration utility that you can use to configure the router’s settings. Simply log in

Internet Setup There are six Internet Connection Types: DHCP, PPPoE, Static IP, PPTP, L2TP, and Telstra Cable. Automatic Configuration - DHCP When y

Static IP Select Static IP if your ISP provided you the static IP address, Subnet Mask, Default Gateway and DNS server addresses for Internet connecti

L2TP L2TP is a service that applies to connections in Israel only. Enter the Internet connection information provided by your ISP accordingly. Telst

Network Setup Router IP You can change the Router’s IP Address and its Subnet Mask for the local network. DHCP Server Setting The Router has a built-

Step 1 Enter the Static IP Address in the Assign this IP field. Step 2 Enter the MAC address of the corresponding computer in the To this MAC field. S

6.1.2 Setup > DDNS Dynamic DNS (DDNS) allows any user who wishes to access your server to reach it by a registered DNS name instead of an IP addres

6.1.3 Setup > MAC Address Clone Some ISPs require a registered MAC address to access the Internet. You can use the following steps to clone your PC

2Table of Contents 1. Introduction...

6.1.4 Setup > Advanced Routing You can configure your own static routing table using the Advanced Routing function. To see the current routing tab

6.2. Wireless 6.2.1 Wireless > Basic Wireless Settings 21

Wireless Configuration - Manual To configure the Wireless settings, click radio button Manual. You can configure the router’s basic wireless settings

Standard Channel: If you selected Auto – 20/40MHz Channel for the Radio Band setting, then this setting will be your primary Wireless N channel. If y

Encryption: Choose 64 bits or 128 bits Passphrase: You can enter a passphrase and click on the Generate button and the router will automatically gene

WPA2 Personal Select WPA2 Personal from the Security Mode. Encryption: Select either TKIP or AES as the encryption method. Passphrase: Enter a passph

WPA Enterprise Select WPA Enterprise from the Security Mode. Encryption: Select either TKIP or AES as the encryption method. RADIUS Server: Enter the

WPA2 Enterprise Select WPA2 Enterprise from the Security Mode. Encryption: Select either TKIP or AES as the encryption method. RADIUS Server: Enter

Radius This option features WEP used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.

Wireless Configuration - WiFi-Protected Setup To use Wi-Fi Protected Setup, click on WiFi-Protected Setup radio button in ‘Basic Wireless Settings’ pa

3 1. Introduction Thank you for purchasing Asante AWRT-600N Smart Dual Band Wireless N Router. The AWRT-600N Dual Band Wireless N Router provides swi

3 Wireless > MAC Filter You can restrict certain wireless clients from accessing the router by specifying their MAC address and enabling access r

6.2.4 Wireless > Advanced Wireless Settings You can configure various advanced wireless settings on this screen. AP Isolation: This isolates all w

32Basic Rate: The Basic Rate setting is not one, but a series of rates at which the Router can transmit. (The Basic Rate is not the actual rate of d

6.3 Security 6.3.1 Security > Firewall SPI Firewall Protection: Select to enable or disable Stateful Packet Inspection. When enabled, access to t

6.4 Access Restrictions 6.4.1 Access Restrictions > Internet Access Policy You can setup policies that deny or allow specific clients to access th

Access Policy: Select a policy number from the drop down list. Enter Policy Name: Enter a name for the policy. Status: Choose to Enable or Disable the

Website Blocking You can block the specified clients from accessing certain websites by URL or Keyword. Enter the URL or the Keyword you wish to block

Click Save Settings to save the settings. 37

6.5 Applications & Gaming 6.5.1 Applications & Gaming > Single Port Forwarding If you want to host ftp server or online gaming, you must op

External Port/ Internal Port: If you are only forwarding one port, you can put the same port number in both the External and Internal Port boxes. Pr

2. Connecting the Router Note: Prior to connecting the router, be sure to power

Start ~ End Port: If you are only forwarding one port, you can put the same port number in both the Start and End Port boxes. Protocol: If you are n

DMZ: Select to enable or disable DMZ. Source IP Address: Specify the IP address that can communicate with the DMZ host. Destination: Specify the IP Ad

42Wireless WMM Support: WMM is a wireless Quality of Service feature that improves quality for audio, video, and voice applications by prioritizing

Category There are five categories available. Select one of the following: Applications, Online Games, MAC Address, Ethernet Port, or Voice Device. A

Add a New Application Enter a Name: Enter a name for this application. Port Range: Enter the port range that the application will be using. For examp

Online Games Games: Select the appropriate game. Priority: Select the appropriate priority: High, Medium, Normal, or Low. Click Add to save your chan

MAC Address Enter a Name Enter a name for your network device. MAC Address Enter the MAC address of your network device. Priority Select the appropri

Ethernet Port Ethernet: Select the Ethernet port that you want to configure. Priority: Select the appropriate priority: High, Medium, Normal, or Low

Voice Device Enter a Name: Enter a name for your voice device such as VoIP or IP Phone. MAC Address: Enter the MAC address of your voice device. Prio

6.6 Administration 6.6.1 Administration > Management The Management screen allows you to change the router’s log in password as well as other admin

3. Configuring the Router After all components in the previous picture are connected and powered up, follow the steps below to configure the router.

Remote Access: Select to enable or disable remote management/upgrade of the router. You can allow remote management from any IP Address or a specifie

6.6.3 Administration > Diagnostics The Diagnostics screen allows you to perform Ping and Traceroute tests. Ping Test: Enter the IP or URL Address

6.6.4 Administration > Factory Defaults The Factory Defaults screen allows you to set all the router’s settings to the factory default. Click on

6.6.5 Administration > Firmware Upgrade The Firmware Upgrade screen allows you to upgrade the router’s firmware. You must download and unzip the n

6.7 Status 6.7.1 Status > Router The Router screen displays various status of the router including the firmware version. Click on the Refresh butt

6.7.2 Status > Local Network The Local Network screen displays various status about your Local Area Network. Click on the DHCP Client Table to dis

6.7.3 Status > Wireless Network The Wireless Network screen displays various status about your wireless network. 56

7. Specifications Standards  IEEE 802.11n draft 2.0  IEEE 802.11a / b / g Frequency  2.4 / 5 GHz (Switchable) Ports  1 x 10/100Mbps WAN p

58App Appendix – Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the lim

59This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause

Step 2 Enter admin for both the username and password fields and click OK. The page below should appear. The sections below cover the ‘Advanced Set

- Broadband Radio Access Networks (BRAN);5 GHz high performance RLAN;Harmonized EN covering essential requirementsof article 3.2 of the R&TTE D

61 Technical Support E-mail: [email protected] Toll Free: 1-877-262-0324 Web Site: www.asante.com *Theoretical maximum wireless signal rate derived

If your ISP requires a registered MAC Address, click on the MAC Address Clone tab select Enabled, and click on the Clone My PC’s

DSL For DSL users, follow the steps below to configure the router. Step 1 Select PPPoE from the drop-down menu. 8

Step 2 Enter your username and password provided by your ISP. Note: Depending on the ISP, you may need to include the domain name with your use